lightweight PE Heat Shrinkable Sleeve hot-melt method to connect,anticorrosive
Wholesale pipe joint materials
Heat Shrinkable Sleeve Insulation Connector
1. HSSC-1 Heat shrinkable sleeve (2 layers), which are developed and manufacture by Qingdao Huashida machinery Co., Ltd for anti-corrosion of pipeline, are the composition of radiation cross-linked polyethylene backing and high shearing strengthen melt adhesive, and have the function of shape memory. The hot melt adhesive is squeezed into the joint by the shrink power to form a perfectly sealed surface, after being heated. HSSC-1 is compatible with standard pipe coating, also can be used for coating bare, replacement pipe section and large radius bends. The system is designed to be applied with minimum preheating and is ideal for large diameter wastewater pipe
Application scope
The heat shrinkable sleeve is designed to be applied with minimum preheating and is ideal for large diameter wastewater pipe. 3PE pipe and pre-insulated pipeline joint closure.
| | ITEM | Standard | UNIT | Data |
| Adhesive | softening point | ASTM E 28 | °C | 70-80 |
| shear strength | DIN 30 672 | N/cm | ≥100 |
| Basic | specific density | ASTM D792 | r/cm 3 | 0.935-0.96 |
| tensile strength | ASTM D638 | Mpa | 15-20 |
| Elongation at break | ASTM D792 | % | 350 |
| hardness | ASTM D2240 | ball | 48 |
| Heat Shrinkable Sleeve | peel strength | ASTM D1000 | N/cm | >150 |
| water-intake rate | ASTM D570 | % | 0.05 |
Feature
1.Fast shrinkage speed,
2.good waterproof performance,
3 good anti-corrosive performance,
4.long service life, convenient transportation and fast construction.
2. 3Layer Fiber
reinforced PE heat shrinkable tape (sleeve) is composed of cross-linked polyethylene back, a middle layer of fiber and special heat melt adhesive an. The 3 layer reinforced sleeve gives better shrink ratio, and better strength. It is resistant to corrosion, wear, impact, UV and aging, easier to be operated.
Application area:
It is mainly used for Hollow wall spiral pipe, corrugated pipe and metal reinforced corrugated spiral pipe etc.
TEST PROCEDURE
1. Clean the steel pipe and heat it by fire till over 80 ºC
2. Paint the steel pipe with Primer (mixed with A&B)
3. Fire heat the heat shrink sleeve, be attention to start heating from middle of the sleeve, but act from up and down, and gradually move from middle to two sides of sleeve, in order to drive air out of the sleeve, after finish heating, the good result is that there is about 1-2mm hot adhesive melt at the edge of sleeve.
Heat shrinkable Sleeve construction
Before construction, scissors, flame spray gun, gas bottle, cleaning cloth, wire brush, protective gloves, shovel and other construction tools should be prepared.
The surface of the pipe was preheated to improve the adhesive adhesion and the peeling strength of the pipe. The part of the pipe to be welded was preheated with a flame spray gun at a temperature of 50℃-60℃.
After the pipe is preheated, move the shrink sleeve to the pipe interface to be welded. The shrink sleeve is centered at the center of the joint of the two pipes, and the margin on both sides is even.
Start heating, use the moderate flame of the flame spray gun to heat the heat shrinkable sleeve, first heat the middle part of the shrinkable sleeve, so that the middle part of the shrinkable sleeve around the tube, close to the pipe, when heating the gun mouth should leave the heat shrinkable sleeve 5-10 cm or so, prohibit the hot spray gun to scratch the shrinkable sleeve, and in the baking to swing evenly up and down. Melt the hot melt adhesive substrate evenly and shrink to tight.
After the middle part is tightened, the flame spray gun is gradually baked to both sides, the hand-held flame spray gun should swing back and forth, prohibit the flame of the spray gun mouth to stay in one place or continue to bake a certain part, which will cause the shrinkage sleeve to heat up sharply and carbonize to break, when baking on both sides, it can not be too urgent, from the inside out gradually to the outside, the middle can not have bubbles into the hanging part, Until the shrinkable sleeve is uniformly and tightly attached to the tube.
Huashida Machinery, with over 20 years' experience, is one of the professional oil gas 3pe pipeline girth welding coating heat shrink sleeve manufacturers in China. Offering the customized service, we warmly welcome you to get the high qualified products from our factory.
Looking forward to cooperating with you.
Product Tags:
|
|
Wraparound Heat Shrinkable Sleeve For 3PE Oil Gas Pipe Girth Weld Straight Joint Field Coating Images
|
